X300 unknown product code in EEPROM: 2104

GNU Radio
1

Dose any one know what is the problem with this device.Hardware NI USRP
2940R = x310OS Ubuntu 14.04LTSConnection SFP0

what are these warnings X300 unknown product code in EEPROM: 2104

RX dboard ID: Unknown (0xffff)

./usrp_burn_mb_eeprom --read-all linux; GNU C++ version 4.8.2;
Boost_105400; UHD_003.008.002-80-ge28d7844
Creating USRP device from address:
UHD Warning: X300 unknown product code in EEPROM: 2104
UHD Warning: X300 unknown product code in EEPROM: 2104-- X300
initialization sequence…-- Determining maximum frame size… 1472
bytes.-- Setup basic communication…-- Loading values from EEPROM…
UHD Warning: X300 unknown product code in EEPROM: 2104-- Setup RF
frontend clocking…-- Radio 1x clock:200-- Initialize Radio
control…-- Performing register loopback test… pass
UHD Warning: Unknown transceiver board ID combination. Is your
daughter-board mounted properly? RX dboard ID: Unknown (0xffff) TX
dboard ID: WBX v4 (0x0062)-- Performing register loopback test… pass
UHD Warning: Unknown transceiver board ID combination. Is your
daughter-board mounted properly? RX dboard ID: Unknown (0xffff) TX
dboard ID: WBX + Simple GDB, WBX v3 + Simple GDB, WBX v4 + Simple GDB,
WBX-120 + Simple GDB (0x004f)-- Initializing clock and time using
internal sources… done
Fetching current settings from EEPROM… EEPROM [“revision”] is “52”
EEPROM [“product”] is “2104” EEPROM [“mac-addr0”] is
“00:80:2f:0a:f5:0c” EEPROM [“mac-addr1”] is “10:80:2f:0a:f5:0d”
EEPROM [“gateway”] is “192.168.10.1” EEPROM [“ip-addr0”] is
“192.168.10.2” EEPROM [“subnet0”] is “255.255.255.0” EEPROM
[“ip-addr1”] is “192.168.20.2” EEPROM [“subnet1”] is “255.255.255.0”
EEPROM [“ip-addr2”] is “192.168.30.2” EEPROM [“subnet2”] is
“255.255.255.0” EEPROM [“ip-addr3”] is “192.168.40.2” EEPROM
[“subnet3”] is “255.255.255.0” EEPROM [“serial”] is “F54E25”
EEPROM [“name”] is “”

Warm RegardsJunaid

2

Dear Marcus,
I am using NI USRP 2940 in linux having the
UHD UHD_003.008.002-80-ge28d7844 dose i still need the specific eeprom
value from NI or may i use given by ettus.

is the UHD warnning below is because of db EEprom or EEprom mb?UHD
Warning:
X300 unknown product code in EEPROM: 2104
i am using NI USRP 2940R with WBX 40 initially its works good once i
move to Linux and updated the FPGA afterwords this warning came to
notice and RX doesn’t work.i also having a x310 with SBX 120 with me its
work fine, what if i put all parameters of eeprom by ettus in NI will it
work on linux ? Regards Junaid

 On Monday, February 23, 2015 11:12 PM, Ettus Support - Marcus

Müller [email protected] wrote:

Hi Muhammad,

this looks like both your USRP’s mainboard EEPROM and your
daughterboard’s EEPROM have seen a bit of change.
That’s something you can fix!
The WBX-40 has an RX daughterboard ID of 0x0063, so that’s something
you could directly fix by employing usrp_burn_db_eeprom (make sure it’s
actually the 40 MHz variant, and not the 120 one! Obviously, we
shouldn’t trust the EEPROM contents here.).

Now, the NI-USRP 2940R uses a specific eeprom value, which is 0x772B
for the 40-MHz-daughterboards variant.

Greetings,
Marcus

On 02/23/2015 06:06 PM, Muhammad JUNAID wrote:

Dose any one know what is the problem with this device. Hardware NI
USRP 2940R = x310 OS Ubuntu 14.04LTS Connection SFP0

what are these warnings X300 unknown product code in EEPROM: 2104

  RX dboard ID: Unknown (0xffff)

./usrp_burn_mb_eeprom --read-all linux; GNU C++ version 4.8.2;
Boost_105400; UHD_003.008.002-80-ge28d7844
Creating USRP device from address:
UHD Warning: X300 unknown product code in EEPROM: 2104
UHD Warning: X300 unknown product code in EEPROM: 2104 – X300
initialization sequence… – Determining maximum frame size… 1472
bytes. – Setup basic communication… – Loading values from EEPROM…
UHD Warning: X300 unknown product code in EEPROM: 2104 – Setup RF
frontend clocking… – Radio 1x clock:200 – Initialize Radio
control… – Performing register loopback test… pass
UHD Warning: Unknown transceiver board ID combination. Is your
daughter-board mounted properly? RX dboard ID: Unknown (0xffff)
TX dboard ID: WBX v4 (0x0062) – Performing register loopback test…
pass
UHD Warning: Unknown transceiver board ID combination. Is your
daughter-board mounted properly? RX dboard ID: Unknown (0xffff)
TX dboard ID: WBX + Simple GDB, WBX v3 + Simple GDB, WBX v4 + Simple
GDB, WBX-120 + Simple GDB (0x004f) – Initializing clock and time using
internal sources… done
Fetching current settings from EEPROM… EEPROM [“revision”] is
“52” EEPROM [“product”] is “2104” EEPROM [“mac-addr0”] is
“00:80:2f:0a:f5:0c” EEPROM [“mac-addr1”] is “10:80:2f:0a:f5:0d”
EEPROM [“gateway”] is “192.168.10.1” EEPROM [“ip-addr0”] is
“192.168.10.2” EEPROM [“subnet0”] is “255.255.255.0” EEPROM
[“ip-addr1”] is “192.168.20.2” EEPROM [“subnet1”] is “255.255.255.0”
EEPROM [“ip-addr2”] is “192.168.30.2” EEPROM [“subnet2”] is
“255.255.255.0” EEPROM [“ip-addr3”] is “192.168.40.2” EEPROM
[“subnet3”] is “255.255.255.0” EEPROM [“serial”] is “F54E25”
EEPROM [“name”] is “”

Warm Regards Junaid