No UHD Devices Found

GNU Radio
#1

Hi,
I have received two new USRP2 (rev 4) with a BasicRx DB. I connect the
DB,
set the gbit lan so that :

eth1 Link encap:Ethernet HWaddr 00:15:17:e6:86:56
inet addr:192.168.10.1 Bcast:192.168.10.255
Mask:255.255.255.0
inet6 addr: fe80::215:17ff:fee6:8656/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:190 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:27244 (27.2 KB)
Memory:f3000000-f3020000

I connect the USRP2 to the GBIT lan port and try:
ping 192.168.10.2

PING 192.168.10.2 (192.168.10.2) 56(84) bytes of data.
From 192.168.10.1 icmp_seq=2 Destination Host Unreachable
From 192.168.10.1 icmp_seq=3 Destination Host Unreachable
From 192.168.10.1 icmp_seq=4 Destination Host Unreachable

am I missing something ?

(I have also builded UHD and tried uhd_find_devices…result: No UHD
Devices
Found )

Any suggestions ?? (same behaviours on both uspr2)
thanks in advance Luca

#2

Are the UHD images burned onto the sd card?

http://code.ettus.com/redmine/ettus/projects/public/wiki/U2binaries#UHD-Firmware-and-FPGA-Images

http://www.ettus.com/uhd_docs/manual/html/usrp2.html#load-the-images-onto-the-sd-card

Are lights E and F light up on the front panel once powered up?

-Josh

#3

Hi,

I’ve got exactly the same problem.
In my case the lights D and F are light up.

The usrp2_card_burner_gui.py works correctly. I’ve checked that by
flashing the cards with the common firmware.
And that works fine.

Tobias

Am 15.07.2010 18:32, schrieb Josh B.:

#4

Hello,

“destination host unreachable” indicates that the route is not set
correctly. Try

route add -net 192.168.10.0/24 dev eth1

or check

route -n

to see if the routing is using the proper network devices.

Matthias

Am 28.07.2010 um 11:10 schrieb Tobias S.:

#5

Hello,

thanks for your quick answer.

I checked it and I think ists okay.

inupc33:/home/gnuradio/gnuradio/uhd/host/utils # route -n
Kernel IP Routentabelle
Ziel Router Genmask Flags
Metric Ref Use Iface
129.69.175.0 0.0.0.0 255.255.255.0 U 0
0 0 eth0
192.168.10.0 0.0.0.0 255.255.255.0 U 0
0 0 eth1
169.254.0.0 0.0.0.0 255.255.0.0 U 0
0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U
0 0 0 lo
0.0.0.0 129.69.175.254 0.0.0.0 UG 0
0 0 eth0

And in contrast to Luca I used the
ping -I eth1 192.168.10.2 -command to be sure that is use the right
network device.

Tobias

-----Ursprüngliche Nachricht-----
Von: Matthias W. [email protected]
Gesendet: 28.07.2010 11:30:50
An: [email protected]
Betreff: Re: [Discuss-gnuradio] No UHD Devices Found

to see if the routing is using the proper network devices.

http://www.ettus.com/uhd_docs/manual/html/usrp2.html#load-the-images-onto-the-sd-card

eth1 Link encap:Ethernet HWaddr 00:15:17:e6:86:56
ping 192.168.10.2

http://lists.gnu.org/mailman/listinfo/discuss-gnuradio

Discuss-gnuradio mailing list
[email protected]
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio

WEB.DE DSL ab 19,99 Euro/Monat. Bis zu 150,- Euro Startguthaben und
50,- Euro Geldprämie inklusive! https://freundschaftswerbung.web.de