# X300 unknown product code in EEPROM: 2104 **URL:** \ **Category:** GNU Radio\ **Created:** [February 23, 2015, 6:10pm UTC](https://www.ruby-forum.com/t/x300-unknown-product-code-in-eeprom-2104/234313 "2015-02-23T18:10:48Z")\ **Posts on this page:** 2\ **Page:** 1
**Author:** ![addis\_a](https://www.ruby-forum.com/letter_avatar_proxy/v4/letter/a/c4cdca/32.png) [@addis\_a](https://www.ruby-forum.com/u/addis_a)\ **Post date:** [February 23, 2015, 6:10pm UTC](https://www.ruby-forum.com/t/x300-unknown-product-code-in-eeprom-2104/234313/1 "2015-02-23T18:10:48Z")
Dose any one know what is the problem with this device.Hardware NI USRP 2940R = x310OS Ubuntu 14.04LTSConnection SFP0 what are these warnings X300 unknown product code in EEPROM: 2104 ``` RX dboard ID: Unknown (0xffff) ``` ./usrp\_burn\_mb\_eeprom --read-all linux; GNU C++ version 4.8.2; Boost\_105400; UHD\_003.008.002-80-ge28d7844 Creating USRP device from address: UHD Warning: X300 unknown product code in EEPROM: 2104 UHD Warning: X300 unknown product code in EEPROM: 2104-- X300 initialization sequence…-- Determining maximum frame size… 1472 bytes.-- Setup basic communication…-- Loading values from EEPROM… UHD Warning: X300 unknown product code in EEPROM: 2104-- Setup RF frontend clocking…-- Radio 1x clock:200-- Initialize Radio control…-- Performing register loopback test… pass UHD Warning: Unknown transceiver board ID combination. Is your daughter-board mounted properly? RX dboard ID: Unknown (0xffff) TX dboard ID: WBX v4 (0x0062)-- Performing register loopback test… pass UHD Warning: Unknown transceiver board ID combination. Is your daughter-board mounted properly? RX dboard ID: Unknown (0xffff) TX dboard ID: WBX + Simple GDB, WBX v3 + Simple GDB, WBX v4 + Simple GDB, WBX-120 + Simple GDB (0x004f)-- Initializing clock and time using internal sources… done Fetching current settings from EEPROM… EEPROM [“revision”] is “52” EEPROM [“product”] is “2104” EEPROM [“mac-addr0”] is “00:80:2f:0a:f5:0c” EEPROM [“mac-addr1”] is “10:80:2f:0a:f5:0d” EEPROM [“gateway”] is “192.168.10.1” EEPROM [“ip-addr0”] is “192.168.10.2” EEPROM [“subnet0”] is “255.255.255.0” EEPROM [“ip-addr1”] is “192.168.20.2” EEPROM [“subnet1”] is “255.255.255.0” EEPROM [“ip-addr2”] is “192.168.30.2” EEPROM [“subnet2”] is “255.255.255.0” EEPROM [“ip-addr3”] is “192.168.40.2” EEPROM [“subnet3”] is “255.255.255.0” EEPROM [“serial”] is “F54E25” EEPROM [“name”] is “” Warm RegardsJunaid ---
**Author:** ![Muhammad\_JUNAID](https://www.ruby-forum.com/letter_avatar_proxy/v4/letter/m/8dc957/32.png) [@Muhammad\_JUNAID](https://www.ruby-forum.com/u/Muhammad_JUNAID)\ **Post date:** [February 24, 2015, 1:43pm UTC](https://www.ruby-forum.com/t/x300-unknown-product-code-in-eeprom-2104/234313/2 "2015-02-24T13:43:52Z")
Dear Marcus, I am using NI USRP 2940 in linux having the UHD UHD\_003.008.002-80-ge28d7844 dose i still need the specific eeprom value from NI or may i use given by ettus. is the UHD warnning below is because of db EEprom or EEprom mb?UHD Warning: X300 unknown product code in EEPROM: 2104 i am using NI USRP 2940R with WBX 40 initially its works good once i move to Linux and updated the FPGA afterwords this warning came to notice and RX doesn’t work.i also having a x310 with SBX 120 with me its work fine, what if i put all parameters of eeprom by ettus in NI will it work on linux ? Regards Junaid ``` On Monday, February 23, 2015 11:12 PM, Ettus Support - Marcus ``` Müller [removed\_email\_address@domain.invalid](mailto:removed_email_address@domain.invalid) wrote: Hi Muhammad, this looks like both your USRP’s mainboard EEPROM and your daughterboard’s EEPROM have seen a bit of change. That’s something you can fix! The WBX-40 has an RX daughterboard ID of 0x0063, so that’s something you could directly fix by employing usrp\_burn\_db\_eeprom (make sure it’s actually the 40 MHz variant, and not the 120 one! Obviously, we shouldn’t trust the EEPROM contents here.). Now, the NI-USRP 2940R uses a specific eeprom value, which is 0x772B for the 40-MHz-daughterboards variant. Greetings, Marcus On 02/23/2015 06:06 PM, Muhammad JUNAID wrote: Dose any one know what is the problem with this device. Hardware NI USRP 2940R = x310 OS Ubuntu 14.04LTS Connection SFP0 what are these warnings X300 unknown product code in EEPROM: 2104 ``` RX dboard ID: Unknown (0xffff) ``` ./usrp\_burn\_mb\_eeprom --read-all linux; GNU C++ version 4.8.2; Boost\_105400; UHD\_003.008.002-80-ge28d7844 Creating USRP device from address: UHD Warning: X300 unknown product code in EEPROM: 2104 UHD Warning: X300 unknown product code in EEPROM: 2104 – X300 initialization sequence… – Determining maximum frame size… 1472 bytes. – Setup basic communication… – Loading values from EEPROM… UHD Warning: X300 unknown product code in EEPROM: 2104 – Setup RF frontend clocking… – Radio 1x clock:200 – Initialize Radio control… – Performing register loopback test… pass UHD Warning: Unknown transceiver board ID combination. Is your daughter-board mounted properly? RX dboard ID: Unknown (0xffff) TX dboard ID: WBX v4 (0x0062) – Performing register loopback test… pass UHD Warning: Unknown transceiver board ID combination. Is your daughter-board mounted properly? RX dboard ID: Unknown (0xffff) TX dboard ID: WBX + Simple GDB, WBX v3 + Simple GDB, WBX v4 + Simple GDB, WBX-120 + Simple GDB (0x004f) – Initializing clock and time using internal sources… done Fetching current settings from EEPROM… EEPROM [“revision”] is “52” EEPROM [“product”] is “2104” EEPROM [“mac-addr0”] is “00:80:2f:0a:f5:0c” EEPROM [“mac-addr1”] is “10:80:2f:0a:f5:0d” EEPROM [“gateway”] is “192.168.10.1” EEPROM [“ip-addr0”] is “192.168.10.2” EEPROM [“subnet0”] is “255.255.255.0” EEPROM [“ip-addr1”] is “192.168.20.2” EEPROM [“subnet1”] is “255.255.255.0” EEPROM [“ip-addr2”] is “192.168.30.2” EEPROM [“subnet2”] is “255.255.255.0” EEPROM [“ip-addr3”] is “192.168.40.2” EEPROM [“subnet3”] is “255.255.255.0” EEPROM [“serial”] is “F54E25” EEPROM [“name”] is “” Warm Regards Junaid