# Two ADCs, one signal

**URL:** <https://www.ruby-forum.com/t/two-adcs-one-signal/88065>\
**Category:** GNU Radio\
**Created:** [March 7, 2007, 10:07pm UTC](https://www.ruby-forum.com/t/two-adcs-one-signal/88065 "2007-03-07T22:07:01Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![unknown](https://www.ruby-forum.com/letter_avatar_proxy/v4/letter/u/4bbf92/32.png) [@unknown](https://www.ruby-forum.com/u/unknown)\
**Post date:** [March 7, 2007, 10:07pm UTC](https://www.ruby-forum.com/t/two-adcs-one-signal/88065/1 "2007-03-07T22:07:01Z")

</div>

Brian P. wrote on Mon, 5 Mar 2007 16:05:09 -0500:

> That Analog Devices AD9235-65 looks like it’s good if you want to  
> sample at something like the USRP is doing right now - 64MHz. So what  
> you’d be looking at is an oscope with a 500MHz bandwidth and a 64MSPS  
> sampling rate. You could possibly double that if you did some  
> cascading of the ADCs and used the opposite edge of the clock to also  
> clock into a different ADC - giving you (effectively) double the  
> samples per second.

If one was to shift the second ADC by 90 degrees to the clock instead  
of 180, wouldn’t one be gaining I/Q data aswell as increase the  
effective sampling rate?

–  
Nos

---

<div class="post-metadata">

**Author:** ![unknown](https://www.ruby-forum.com/letter_avatar_proxy/v4/letter/u/4bbf92/32.png) [@unknown](https://www.ruby-forum.com/u/unknown)\
**Post date:** [March 7, 2007, 10:44pm UTC](https://www.ruby-forum.com/t/two-adcs-one-signal/88065/2 "2007-03-07T22:44:12Z")

</div>

On 3/7/07, removed\_email\_address@domain.invalid [removed\_email\_address@domain.invalid](mailto:removed_email_address@domain.invalid) wrote:

> If one was to shift the second ADC by 90 degrees to the clock instead  
> of 180, wouldn’t one be gaining I/Q data aswell as increase the  
> effective sampling rate?

I found a post on [dsprelated.com](http://dsprelated.com) that can help. I will post relavent  
information here.

Taken from [comp.dsp | Nyquist rate for sampling complex-valued data?](http://www.dsprelated.com/showmessage/24329/1.php)

– snip –

> I (vaguely) heard that sampling complex-valued data does not abide by the  
> Nyquist rate criteria, i.e., the sampling rate fs can go lower than Nyquist  
> rate and it still can avoid aliasing and reconstruct perfectly…
> 
> Is that true?

Yes. Real sampling at Fs samples/second provides a “usable” bandwidth  
of Fs/2 Hz while complex sampling provides a usable bandwidth of Fs Hz  
at the same sample rate.

> Any theory behind it?

Yes. Use two pieces of knowledge: a) the Fourier transform property  
that H(f) = H\*(-f) (this is known as “Hermitian symmetry”) for a real  
signal h(t), H(f) = F[h(t)], and b) the fact that sampling can be  
viewed in the frequency domain as replicating the band from -Fs/2 to  
+Fs/2 every Fs Hz.

More simply, a real signal has bandwidth from 0 to Fs/2 available, while  
a complex signal has bandwidth from -Fs/2 to +Fs/2 available.

## As I recall, Richard Lyon’s book “Understanding Digital Signal Processing” (2nd ed.) discusses this phenomenom at great length.

% Randy Yates  
– snip –

> –  
> Nos

Brian

---

<div class="post-metadata">

**Author:** ![unknown](https://www.ruby-forum.com/letter_avatar_proxy/v4/letter/u/4bbf92/32.png) [@unknown](https://www.ruby-forum.com/u/unknown)\
**Post date:** [September 25, 2007, 11:10pm UTC](https://www.ruby-forum.com/t/two-adcs-one-signal/88065/3 "2007-09-25T23:10:21Z")

</div>

On 3/8/07, removed\_email\_address@domain.invalid [removed\_email\_address@domain.invalid](mailto:removed_email_address@domain.invalid) wrote:

> Fascinating subject. I think I’d very much like to experiment with  
> multiple ADCs and different clockings…

It becomes a very tricky subject and is very susceptible to clocking  
and phase noise.

> If one puts an ADC at 0, 90, 180 and 270 degrees on the clock, one  
> should be getting four times the sample rate and twice the bandwidth  
> of just one ACD, yes? I don’t see any reason why it wouldn’t work, but  
> I’ve become used to surprises.

If you have a sample clock running at Fs, you effectively have Fs/2  
bandwidth for real signal sampling. If you add in both rising and  
falling edges of the clock (0 and pi phase shifts), you can double  
your Fs to 2_Fs and double your sampled bandwidth to Fs. Now, if you  
do the peak and trough of such a thing, you end up with 4 points you  
are sampling, doubling your previous sampling rate and doubling your  
previous bandwidth to be 2_Fs - where Fs was your original sampling  
frequency.

Both are an increase of 4x.

The problem I see with the above is this: to get accurate clocking,  
you need a sharp edge to take the sample. A square wave works very  
nicely for this. To get the 180 degree shift clock, you simply take  
the falling edge of that square wave. This is relatively simple to do  
and is used in many places.

When generating the 90 and 270 degree shifts, that requires a little  
bit of problem solving since you don’t really have a clear  
transitioning point in the middle of those flat tops to be able to  
take an integral or derivative of such a wave.

Now, if you were to take a fixed frequency sinusoidal clocking source  
and run it through a capacitor, the output of this capacitor should be  
at a 90 degree phase shift from the original signal. If you then sent  
those two clocking sources through a squaring circuit, you could  
possibly get a pretty decent set of sources out of that. NOTE: I have  
never done this and the thought just popped in my head - I am sure it  
is very rudimentary and quite possibly does not even work.

Either way, to fully exploit that, you would have to send those  
through some inverting buffer that would give them all rising edges  
where they needed to be instead of both rising and falling edges. As  
you can see, with all the different stages the signals have to go  
through - there is a good amount of uncertainty that comes with the  
phase delays of each path which all have to be matched. Significant  
engineering time would have to go into the modeling and simulation of  
this along with building, debugging and late night bouts of  
frustration.

As another note, there may already be some discrete chips that perform  
such phase shifts with very low phase noise. Let me know if you find  
anything.

> I wonder if some sort of beat frequency would emerge if I ran two ADCs  
> at different sample rates on the same signal, and what for the beat  
> frequency would manifest in… Or for that matter, if one used ACDs  
> the respective number of bits of each would divide into an infinite  
> decimal representation when the peak-to-peak voltage of each is equal.  
> By manipulating parameters like these in real-time one might be able  
> to gain a lot of information from repetitive signals. Maybe even do a  
> “derivate scan” at whatever precision you managed to manipulate your  
> clock at…

You lost me here.

> Noise is a problem smashing the mathematical neatness into bytes, but  
> I seem to remember something about ‘sample aperture’, I think it was.  
> I suspect it does some sort of averaging of the signal, so this window  
> width of the sample would provide some sort of critical frequency  
> too… Maximum undersampling rate, maybe?

Aperture jitter is the delay that it takes your ADC to take it’s  
snapshot of the analog signal after your clock has already occurred.  
This is usually pretty small, but can cause some problems with there  
is a very high IF and you are under sampling.

Usually this is significantly less than your input analog bandwidth  
anyway.

> I’m going to start looking into these issues, but if you happen to  
> know the answers please point me to them. 🙂

“Understanding Digital Signal Processing” by Richard G. Lyons (ISBN:  
0-13-108989-7) spends a significant amount of time discussing periodic  
sampling in Chapter 2. You can probably pick up a whole heck of a lot  
of information from there.

> Thanks for the reply,
> 
> –  
> Nos

Brian
